![]() The power state (on/off) of the Bluetooth adapter is shown below the address and can be changed by checking the Turn on/off box. On the Linux or MacOS platforms the name of the Subsurface computer and its Bluetooth address are shown on the right hand side. If there is a problem in communicating with the dive computer, an error message is shown, similar to this text: "Unable to open /dev/ttyUSB0 Mares (Puck Pro)". Disconnect and switch off the dive computer to conserve its battery power. All the imported dives appear in the Dive List, sorted by date and time. Then click the OK button at the bottom of the dialog. In the case of the image above, the last six dives are checked and will be transferred to the Dive List. Next to each dive is a checkbox: check all the dives that need to be transferred to the Dive List. Each dive comprises a row in the table, showing the date, duration and depth. After the dives have been downloaded, they appear in a tabular format on the right-hand side of the dialog (see image B, above). Remember for some dive computers progress information could be inaccurate since Subsurface doesn’t know how much downloadable data there are until the download is complete. The Download dialog shows a progress bar at the bottom of the dialog. Depending on the make of the dive computer and/or number of recorded dives, this could take some time. With communication established, you can see how the data are retrieved from the dive computer. These are only used as diagnostic tools when there are problems with downloads(see below). The checkbox marked Download into new trip ensures that, after upload, the downloaded dives are grouped together as a new trip(s) in the Dive List.ĭo not check the checkboxes labelled Save libdivecomputer logfile and Save libdivecomputer dumpfile. If the checkbox Always prefer downloaded dives has been checked and, during download, dives with identical date-times exist on the dive computer and on the Subsurface Dive List panel, the dive in the Subsurface divelog will be overwritten by the dive record from the computer. Consequently, for these dive computers, all dives are downloaded irrespective of the status of this check box. Mares Puck) do not provide a contents list to Subsurface before the download in order to select only new dives. If one or more of your dives in Subsurface has been accidentally deleted or if there are older dives that still need to be downloaded from the dive computer, this box needs to be checked. Normally, Subsurface only downloads dives after the date-time of the last dive in the Dive List panel. If all the dives on the dive computer need to be downloaded, check the checkbox Force download of all dives. These buttons only appear once you have downloaded from different dive computers. For some dive computers the data entered here is actually the mount point of the USB storage device as which the dive computer identifies itself.īelow the three drop downs are up to four shortcut buttons that allow you to easily switch between multiple dive computers that you are frequently downloading from. Some dive computers disable this drop-down as they use other means to find and connect to the device. Consult Appendix A and Appendix B for technical details on how to find the appropriate port information for a specific dive computer and, in some cases, how to do the correct settings to the operating system of the computer on which Subsurface is running. The appropriate port name must be selected. The Device or Mount Point drop-down list contains the USB or Bluetooth port name that Subsurface needs in order to communicate with the dive computer. ![]() ![]() D4 (Suunto), Veo200 (Oceanic), or Puck (Mares). On the Dive Computer drop-down list, the model name of the dive computer must be selected, e.g. On the vendor drop-down list select the make of the computer, e.g. The dialog has two drop-down lists, Vendor and Dive Computer. Below is a dive profile for a dive to 20 m for 30 min, followed by a 5 minute safety stop at 5 m. Drag the waypoints to represent an accurate time duration for the dive. To remove a waypoint, right-click on it and choose "Remove this point" from the context menu. Moving can also be done by selecting the waypoint and using the arrow keys. To add a waypoint, double-click on any line segment. If the dive depth was 20 m then you need to drag the appropriate waypoints downward to 20 m. The dive profile itself comprises several line segments demarcated by waypoints (white dots on the profile, as shown above). The units (metric/imperial) on the axes are determined by the Preference settings. The time and depth represented by the cursor are indicated at the top of the black information box and D). ![]() Modifying the dive profile: When the cursor is moved around the dive profile, its position is shown by two right-angled red lines as seen below. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |